Yamaha ttr 125 service repair manual 2006 download. Yamaha TT 2019-03-06

Yamaha ttr 125 service repair manual 2006 download Rating: 4,4/10 286 reviews

Yamaha Ttr

yamaha ttr 125 service repair manual 2006 download

Join our community just now to flow with the file yamaha ttr 125 service repair manual 2003 download and make our shared file collection even more complete and exciting. Place the motorcycle on a flat area 2. Place a suitable support under the engine. Screws pressure plate : 6N. Lift the front wheel placing a support under the engine. Bolt camshaft gear : 60N.

Next

Yamaha TTR 250 2006 Service Manual Free Download

yamaha ttr 125 service repair manual 2006 download

Read the following text in order to check the switches properly. Adjusting nut initial torque : 43 N. It is highly toxic and caustic. Troubleshooting and electrical service procedures are combined with detailed wiring diagrams for ease of use. Place the motorcycle on a flat area. Using the strobe light check if the stationary point 2 stays within the ignition range 3 indicated in the magnet.

Next

Yamaha Ttr

yamaha ttr 125 service repair manual 2006 download

Connect: Compression meter1 Adapter 2 Compression meter: 90890-03081 Adapter. After repairing or replacing a tire, make sure to apply the proper torque to the valve stem lock-nu 1 1 1 1 1. Lift the rear wheel placing a support under the engine. The brake disc should be installed. Use the proper tools and cleaning equipment.

Next

YAMAHA TTR230 SERVICE MANUAL Pdf Download.

yamaha ttr 125 service repair manual 2006 download

Turn the adjuster 4 and completely eliminate the cable 2 free play. You might actually fix your car - and save money in the process. Clean all gasket surfaces and the contact surfaces of the cases. Place the motorcycle on a flat area. Place the motorcycle on a flat area.

Next

Yamaha TT

yamaha ttr 125 service repair manual 2006 download

While moving the piston to its position, mount the dust protector on the assembly. Place the motorcycle on a flat area. Crankshaft spacer 90890-04081 This tool is used for installing the crankshaft. Valve spring clamp 90890-04019 This tool is required for removing and installing valves. Everything from wiring to rebuilding the machine - as well as electrical diagrams, service procedures, fluid capacities, etc. Secondary winding resistance: Ω Ignition coil defective — Replace.

Next

Yamaha Ttr

yamaha ttr 125 service repair manual 2006 download

Place a support under the frame in order to maintain the carburetor upright. Internal diameter of the brake drum: Standard: 110 mm Limit: 111 mm. A corroded jaw may cause the battery terminal to overheat. Place the motorcycle on a flat area 2. Valve spring clamp: 90890-04019 5.

Next

Yamaha Ttr

yamaha ttr 125 service repair manual 2006 download

Spark plug Neutral switch 4. Ready to start scraping some knuckles? Crankcase separator 90890-01135 This tool is required for separating the crankcases. Observe that there is no continuity open circuit for color combinations other than those aforementioned. Milling cutter Desired result 30° To center the seat and establish an 1,0 mm 45° width D The seat is thin and is resting on the valve internal face. Screw master cylinder support : 7 N. Wash the cases thoroughly using kerosene. To 10 mm 6 mm prevent warping, tighten the assembly bo-.

Next

Yamaha Ttr

yamaha ttr 125 service repair manual 2006 download

Repeat the bleeding proce- dure when the small bobbles have vanished from the system. It gives you an excuse to avoid other household chores. A hazardous efficiency loss may occur if the system does not bleed properly. Install: Reverse the removal steps: Case cover covers Head covers Head cover bolts: 10N. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure.

Next

Yamaha Ttr

yamaha ttr 125 service repair manual 2006 download

Lift the rear wheel placing a support under the engine. Lift the front wheel placing a support under the engine. Remove the seat, pulling it towards the rear of the motorcycle. Stop the engine and check the oil level again. Then, in order to check the conditions of the battery, measure the voltage at the terminals. Brake pedal free play: 20 ~ 30 mm 6. The manufacturer assumes no liability for injuri- es or damage resulting from mishandling.

Next