The release fork is actuated by the hydraulic slave cylinder mounted on the transmission housing. Insert alignment tabs at bottom of fan shroud into slots in bracket at bottom of radiator. Start and warm the engine. The ignition coil is not oil filled. The amount of time Charging required for a battery to accept measurable charging Amperage Amperes Amperes Amperes current at various voltages is shown in the Charge Open Rate chart. Remove the support cushion bolts and remove the cushion and the transmission support bracket. Replace any bearing that shows abnormal wear.
Place 4 adapter blocks so they do not damage the bearing cage. Support the 2 Attach wheel lift to rear wheels. The clutches will have radial grooves on the plates, and concentric grooves on the discs or bonded fiber material that is smooth in appearance. Tighten mounting bolts to 23 N·m 17 ft. Drain lubricant to the correct level. Don't waste time calling around to your local bookstores or waiting for a repair manual to arrive by mail.
The speci- fied torque must always be applied when tightening the fasteners. Then check that the and, on four-door models, the rear door power win- glass is not bound tight in the tracks. Wear gloves to prevent injury. Remove the thermo- stat housing and install thermostat. Refer to Clockspring in the Removal and Installation section of this group for the additional service procedures for the clockspring. Refer to Group 8E - Instrument Panel Sys- arms. Two-tire-travel and several-tire-travel models are available, although why someone wants a single of these with two-tire push escapes us.
Install new push rods 6. Remove side gear, clutch pack retainer, and clutch pack. If replacement is necessary, use only an original equipment clamp with matching number or letter. Clean the gasket mating surfaces. Posi- tion alignment dowels into rubber grommets in radi- ator lower crossmember Fig. Tighten the terminal clamp pinch-bolt hex nut to 8. Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner.
Refer to Group 8C, Charging Systems, for correct procedures. Rotate and hold the ignition switch in the Start position. Good reading at this link for you. Verify that pedal installed, or disconnected. If solution is clean, drain coolant into a clean container for reuse.
Swollen rubber parts indicate the presence of petroleum in the brake fluid. Install new sending unit 3. The Cherokee was the first unit body sport-utility vehicle, as specific from the classic body-on-frame technique. Also, the gasket is installed dry. Disc should slide freely on splines.
Refer to Wiring Diagrams in the index of this service manual for the location of the proper wiring repair or connector and terminal service procedures. . Start and warm the engine. Refer to Group 7, receptacles. Refer to Group 23 - Body for the front door window regulator service procedures.
Also, the gasket is installed dry. Before you proceed with this diagnosis, con- firm proper switch operation. A logic block in each microprocessor power booster operate the same as a vehicle without receives identical sensor signals. Refer to Group 8M, Passive Restraint Systems. Use Remover D-149 and Handle C—4171.
Nevertheless, this is not an Explorer, a sport-utility vehicle designed for those who check this out breed as stylish station wagons. To test for contamination, put a small amount of drained brake fluid in clear glass jar. Always use the not pull on the instrument cluster by the lens correct bulb size and type for replacement. Inspect for leaks and continue operating the engine until the thermostat opens. Water pump impeller loose on 8.
If the solution 3 Connect a tachometer and an engine ignition is clean, drain the coolant into a clean container for timing light timing light is to be used as a strobe. For each switch activa- When all of the speed control parameters are met, tion, speed will be lowered approximately 1 mph. There should be no continuity. This angle is not adjustable, damaged component s must be replaced to correct the thrust angle. Refer to procedure in this section 2 Check for rocker arm bridges which are caus- ing misalignment of the rocker arm to valve tip area.